乐视盒子C1s更换电源IC&加装TTL插针实录

乐视盒子C1s更换电源IC&加装TTL插针实录

乐迷飞来一块乐视盒子C1s砖，没问原因，直接插电，亮一颗红灯，通常这种情况是电源部份问题，检测电源附近看到电源IC上有一个窟窿，八个脚把一个给烧毁了。

什么也不用说，直接吹下来换，注意中间有散热接触部份，烙铁是焊接不到的。（右下向上数第2脚pcb敷铜被烧毁）

焊上新电源IC，把那个脚用焊锡飞好。

既然动手了，给这位兄弟加上TTL插针。

找来一块旧声卡，把插针拆下来，正合适。

用烙铁焊接好。

蛮合衬的^_^

插上TTL，打开终端，一串欢快的代码结束了枯燥的维修过程。

• ?EEEE I3000000032940xf300100003877530EEEE I400000004294_M6_BL1_3003>2137333
• TE : 125999
• BT : 10:23:38 May 13 2014
• wait pll-0x03 target is 01d4 now it is 0x000001d3
• DDR clock is 468MHz with Low Power & 2T mode
• DDR training :
• DX0DLLCR:40000000
• DX0DQTR:ffffffff
• DX0DQSTR:3db05001
• DX1DLLCR:40000000
• DX1DQTR:ffffffff
• DX1DQSTR:3db05001
• DX2DLLCR:40000000
• DX2DQTR:ffffffff
• DX2DQSTR:3db05001
• DX3DLLCR:40000000
• DX3DQTR:ffffffff
• DX3DQSTR:3db05001
• Stage 00 Result 00000000
• aml log : Total run [1] Times
• HHH
• Boot From SPI
• ucl decompress...true
• 0x12345678
• Boot from internal device 1st SPI RESERVED
• TE : 372848
• System Started
• U-boot-00000-g4a62c80(m6_letv_g28ref@4a62c808) (May 13 2014 - 10:23:24)
• aml_rtc_init
• aml rtc init first time!
• Clear HDMI KSV RAM
• DRAM:  1 GiB
• relocation Offset is: 105e4000
• usid is: C1S5000
• 1 c1s board_init buf is: C1S5000
• 7 c1 board_init board_type is: 3
• 8 c1 board_init board_type is: 3
• NAND:  Amlogic nand flash uboot driver, Version U1.06.017 (c) 2010 Amlogic Inc.
• No NAND device found!!!
• NAND device id: 98 d7 84 93 72 57
• NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
• 1 NAND chips detected
• #####aml_nand_init, with RB pins and chip->chip_delay:20
• bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
• oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
• aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
• multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
• aml_nand_initobmul =1,chip->ecc.layout->oobfree[0].length=32,aml_chip->oob_size=1280
• aml nand env valid addr: 8000
• key start_blk=1016,end_blk=1023,aml_nand_key_init:684
• aml nand key valid addr: fe000000
• aml nand key valid addr: fe400000
• aml nand key valid addr: fe800000
• aml nand key valid addr: fec00000
• CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
• i=0,register --- nand_key
• NAND bbt detect factory Bad block at 7b000000
• 2 too much bad block!!
• Creating 12 MTD partitions on "nandnormal":
• 0x000000800000-0x000001000000 : "bootargs"
• 0x000001000000-0x000001800000 : "misc"
• 0x000001800000-0x000002000000 : "baseparam"
• 0x000002000000-0x000002800000 : "logo"
• 0x000002800000-0x000003800000 : "aml_logo"
• 0x000003800000-0x000009800000 : "fastplay"
• 0x000009800000-0x00000a800000 : "recovery"
• 0x00000a800000-0x00000b800000 : "boot"
• 0x00000b800000-0x00002b800000 : "system"
• 0x00002b800000-0x00004b800000 : "cache"
• 0x00004b800000-0x00008bc00000 : "userdata"
• NAND bbt detect factory Bad block at 7b000000
• NAND bbt detect factory Bad block at 8b800000
• 0x00008bc00000-0x0000fe000000 : "NFTL_Part"
• NAND bbt detect factory Bad block at a0000000
• NAND bbt detect factory Bad block at a0800000
• NAND bbt detect factory Bad block at a1800000
• NAND bbt detect factory Bad block at d2000000
• NAND bbt detect factory Bad block at ef400000
• nandnormal initialized ok
• detect mx chiprevD :0 and nand_type: 20
• No NAND device found!!!
• NAND device id: 98 d7 84 93 72 57
• NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
• 1 NAND chips detected
• #####aml_nand_init, with RB pins and chip->chip_delay:20
• bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
• oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
• aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
• multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
• aml_nand_initobmul =1,chip->ecc.layout->oobfree[0].length=32,aml_chip->oob_size=1280
• aml nand env valid addr: 8000
• key start_blk=1016,end_blk=1023,aml_nand_key_init:684
• aml nand key valid addr: fe000000
• aml nand key valid addr: fe400000
• aml nand key valid addr: fe800000
• aml nand key valid addr: fec00000
• CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
• name=nand_key nand_key
• NAND bbt detect factory Bad block at 7b000000
• 2 too much bad block!!
• Creating 12 MTD partitions on "nandnormal":
• 0x000000800000-0x000001000000 : "bootargs"
• 0x000001000000-0x000001800000 : "misc"
• 0x000001800000-0x000002000000 : "baseparam"
• 0x000002000000-0x000002800000 : "logo"
• 0x000002800000-0x000003800000 : "aml_logo"
• 0x000003800000-0x000009800000 : "fastplay"
• 0x000009800000-0x00000a800000 : "recovery"
• 0x00000a800000-0x00000b800000 : "boot"
• 0x00000b800000-0x00002b800000 : "system"
• 0x00002b800000-0x00004b800000 : "cache"
• 0x00004b800000-0x00008bc00000 : "userdata"
• NAND bbt detect factory Bad block at 7b000000
• NAND bbt detect factory Bad block at 8b800000
• 0x00008bc00000-0x0000fe000000 : "NFTL_Part"
• NAND bbt detect factory Bad block at a0000000
• NAND bbt detect factory Bad block at a0800000
• NAND bbt detect factory Bad block at a1800000
• NAND bbt detect factory Bad block at d2000000
• NAND bbt detect factory Bad block at ef400000
• nandnormal initialized ok
• detect mx chiprevD :0 and nand_type: 20
• nand_curr_device =0
• MMC:   SDIO Port B: 0, SDIO Port C: 1
• SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
• SF: Detected MX25L3205D with page size 256, total 4 MiB
• SPI NOR Flash have write protect!!!
• In:    serial
• Out:   serial
• Err:   serial
• register usb cfg[0] = 9fe7ef8c
• Net:   Meson_Ethernet
• init suspend firmware done. (ret:0)
• key_init(P_AO_RTI_PIN_MUX_REG (0xc8100014))_val = 0x9f5dbec4
• pre_detect_storage
• reboot_mode=charging
• ir init
• key_init(P_AO_RTI_PIN_MUX_REG (0xc8100014))_val = 0x9f5dbc54
• usid is: C1S5000
• 1 c1s switch_boot_mode env is: C1S5000
• switch_boot_mode env = C1s
• P_AO_RTI_STATUS_REG2: 0x0
• suspend = <NULL>
• NAND read: misc offset 0x0, size 0x2046
• 8262 bytes read: OK
• enter_recovery
• ### main_loop: bootcmd="run compatible_boot"
• Hit any key to stop autoboot:  0
• compatible nand
• Booting from nand ...
• NAND read: logo whole chip
• 8388608 bytes read: OK
• NAND read: boot offset 0x0, size 0x600000
• 6291456 bytes read: OK
• pre-clear hdmi ram
• hdcp get form storage medium: nand
• name=nand_key nand_key
• read:addr:0xfe000000,phy_blk_addr:1016,phy_page_addr:0,aml_nand_get_key:125
• device:nand, init key ok!!
• don't found keyname,uboot_key_read:1502
• prefetch hdcp keys from nand failed
• ## Booting kernel from Legacy Image at 82000000 ...
•    Image Name:   Linux-3.0.50-g15b99ad-dirty
•    Image Type:   ARM Linux Kernel Image (lzma compressed)
•    Data Size:    3354207 Bytes = 3.2 MiB
•    Load Address: 80008000
•    Entry Point:  80008000
•    Verifying Checksum ... OK
•         Ramdisk start addr = 0x82333800, len = 0x10b301
•    Uncompressing Kernel Image ... OK
• machid from environment: 0x4e27
• EFUSE machid is not set.
• Using machid 0x4e27 from environment
• Starting kernel ...
• [    0.000000@0] Initializing cgroup subsys cpu
• [    0.000000@0] Linux version 3.0.50-g15b99ad-dirty (letv@letv.localhost) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #2 SMP PREEMPT Tue May 13 10:26:38 CST 2014
• [    0.000000@0] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
• [    0.000000@0] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
• [    0.000000@0] Machine: Amlogic Meson6 g02 customer platform
• [    0.000000@0] Ignoring unrecognised tag 0x00000000
• [    0.000000@0] early_mem:528: start=0x80000000, size=0x4000000
• [    0.000000@0] early_mem:546: start=0x91000000, size=0xef00000
• [    0.000000@0] early_mem:554: start=0xa0000000, size=0x20000000
• [    0.000000@0] Memory policy: ECC disabled, Data cache writealloc
• [    0.000000@0] PERCPU: Embedded 7 pages/cpu @c131f000 s5600 r8192 d14880 u32768
• [    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 206592
• [    0.000000@0] Kernel command line: root=/dev/cardblksd2 rw rootfstype=ext3 rootwait init=/init console=ttyS0,115200n8 mac=c8:0e:77:02:5b:db logo=osd1,0x84100000,720p,full androidboot.resolution=720p hdmimode=720p cvbsmode=480cvbs hlt vmalloc=256m mem=1024m a9_clk_max=1512000000 vdachwswitch=component hdmitx=
• [    0.000000@0] ******** uboot setup mac-addr: c8:e:77:2:5b:db
• [    0.000000@0] osd1:1
• [    0.000000@0] 720p:6
• [    0.000000@0] full:2
• [    0.000000@0] kernel get hdmimode form uboot is 720p
• [    0.000000@0] kernel get cvbsmode form uboot is 480cvbs
• [    0.000000@0] HDMI DEBUG: hdmitx_boot_para_setup [1918]
• [    0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
• [    0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
• [    0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
• [    0.000000@0] Memory: 64MB 239MB 512MB = 815MB total
• [    0.000000@0] Memory: 815100k/815100k available, 19460k reserved, 524288K highmem
• [    0.000000@0] Virtual kernel memory layout:
• [    0.000000@0]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
• [    0.000000@0]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
• [    0.000000@0]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
• [    0.000000@0]     vmalloc : 0xe0000000 - 0xf0000000   ( 256 MB)
• [    0.000000@0]     lowmem  : 0xc0000000 - 0xdff00000   ( 511 MB)
• [    0.000000@0]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
• [    0.000000@0]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
• [    0.000000@0]       .init : 0xc0008000 - 0xc0037000   ( 188 kB)
• [    0.000000@0]       .text : 0xc0037000 - 0xc0824d2c   (8120 kB)
• [    0.000000@0]       .data : 0xc0826000 - 0xc087f2e0   ( 357 kB)
• [    0.000000@0]        .bss : 0xc087f304 - 0xc0b15be8   (2651 kB)
• [    0.000000@0] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
• [    0.000000@0] Preemptible hierarchical RCU implementation.
• [    0.000000@0]        RCU debugfs-based tracing is enabled.
• [    0.000000@0] NR_IRQS:256
• [    0.000000@0] gic_init: irq_offset=0
• [    0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
• [    0.000000@0] MESON TIMER-A c0839ec0
• [    0.000000@0] Disable timerA
• [    0.000000@0] Console: colour dummy device 80x30
• [    0.000000@0] console [ttyS0] enabled
• [    0.281039@0] Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744)
• [    0.340046@0] pid_max: default: 32768 minimum: 301
• [    0.342262@0] Mount-cache hash table entries: 512
• [    0.347529@0] Initializing cgroup subsys cpuacct
• [    0.351411@0] Initializing cgroup subsys freezer
• [    0.355988@0] CPU: Testing write buffer coherency: ok
• [    0.361178@0] MESON TIMER-B c0839f80
• [    0.364526@0] Disable timerA
• [    0.367383@0] Disable timerB
• [    0.370252@0] Disable timerA
• [    0.373241@0] L310 cache controller enabled
• [    0.377278@0] l2x0: 8 ways, CACHE_ID 0x4100a0c8, AUX_CTRL 0x7e462c01, Cache size: 524288 B
• [    0.385576@0]  prefetch=0x31000006
• [    0.388907@0] ===actlr=0x41
• [    0.391691@0] ===actlr=0x4b
• [    0.394462@0] SCU_CTRL: scu_ctrl=0x69
• [    0.398108@0] pl310: aux=0x7e462c01, prefetch=0x31000006
• [    0.501493@1] CPU1: Booted secondary processor
• [    0.561204@1] MESON TIMER-D c083a100
• [    0.561231@0] Brought up 2 CPUs
• [    0.561239@0] SMP: Total of 2 processors activated (4780.85 BogoMIPS).
• [    0.573196@1] Disable timerD
• [    0.576220@0] devtmpfs: initialized
• [    0.583452@0] clkrate [ xtal ] : 24000000
• [    0.583524@0] clkrate [ pll_sys ] : 1200000000
• [    0.587949@0] clkrate [ pll_fixed ] : 2000000000
• [    0.592568@0] clkrate [ pll_vid2 ] : 378000000
• [    0.596977@0] clkrate [ pll_hpll ] : 378000000
• [    0.601494@0] clkrate [ pll_ddr ] : 468000000
• [    0.605743@0] clkrate [ a9_clk ] : 1200000000
• [    0.610147@0] clkrate [ clk81 ] : 200000000
• [    0.614353@0] clkrate [ usb0 ] : 0
• [    0.617731@0] clkrate [ usb1 ] : 0
• [    0.622093@0] print_constraints: dummy:
• [    0.625076@0] NET: Registered protocol family 16
• [    0.630589@1] [wifi_dev_init] in
• [    0.632749@1] [wifi_clock_enable] in
• [    0.636525@1] ***vcck: vcck_pwm_initregister lm device 0
• [    0.641710@1] register lm device 1
• [    0.647203@1] usb_wifi_power: on.
• [    0.648397@1] chip version=edffb75c
• [    0.651879@1] vdac_switch_init_module
• [    0.655511@1] tv_init_module
• [    0.658261@1] major number 254 for disp
• [    0.662169@1] vout_register_server
• [    0.665547@1] register tv module server ok
• [    0.669894@1] /opt/yuetv_release_c2/src/yuetv_2/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_init
• [    0.678944@1] HDMI DEBUG: amhdmitx_init [1818]
• [    0.683262@1] HDMI Ver: 2013Aug25a
• [    0.686658@1] HDMI DEBUG: amhdmitx_probe [1625]
• [    0.691501@1] Set HDMI:Chip C
• [    0.694111@1] HDMI: get hdmi platform data
• [    0.698183@1] HDMI 5V Power On
• [    0.701235@1] HDMI DEBUG: HDMITX_M1B_Init [3424]
• [    0.705824@1] HDMI DEBUG: HDMITX_M1B_Init [3427]
• [    0.710423@1] HDMI DEBUG: hdmi_hw_init [1204]
• [    0.714834@1] HDMI: get brd phy data
• [    0.718396@1] hdmi phy setting
• [    0.721692@1] HDMI: get brd phy data
• [    0.724968@1] hdmi phy setting
• [    0.729180@1] ------------[ cut here ]------------
• [    0.732759@1] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/fs/sysfs/dir.c:455 sysfs_add_one+0x88/0xbc()
• [    0.742931@1] HDMI: reset intr mask
• [    0.746275@1] sysfs: cannot create duplicate filename '/module/hdmitx/version'
• [    0.753482@1] Modules linked in:
• [    0.756718@1] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
• [    0.766248@1] HDMI DEBUG: hdmi_task_handle [1253]
• [    0.766254@0] HDMI irq 1
• [    0.766264@0] Reg0x196 = 0x2  Reg0x80 = 0x1  Reg0x26 = 0xc
• [    0.766282@0] Reg0x196 = 0x42  Reg0x80 = 0x1  Reg0x26 = 0x4c
• [    0.784569@1] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f90>] (warn_slowpath_fmt+0x30/0x40)
• [    0.794286@1] [<c0061f90>] (warn_slowpath_fmt+0x30/0x40) from [<c0122df4>] (sysfs_add_one+0x88/0xbc)
• [    0.803405@1] [<c0122df4>] (sysfs_add_one+0x88/0xbc) from [<c0121f38>] (sysfs_add_file_mode+0x4c/0x9c)
• [    0.812693@1] [<c0121f38>] (sysfs_add_file_mode+0x4c/0x9c) from [<c000fa64>] (param_sysfs_init+0x70/0x1b0)
• [    0.822331@1] [<c000fa64>] (param_sysfs_init+0x70/0x1b0) from [<c003770c>] (do_one_initcall+0xfc/0x164)
• [    0.831694@1] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
• [    0.840628@1] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
• [    0.849584@1] ---[ end trace 1b75b31a2719ed1c ]---
• [    0.893708@1] bio: create slab <bio-0> at 0
• [    0.894572@1] SCSI subsystem initialized
• [    0.896405@1] usbcore: registered new interface driver usbfs
• [    0.902440@1] usbcore: registered new interface driver hub
• [    0.907409@1] usbcore: registered new device driver usb
• [    0.912900@1] LCD driver init
• [    0.915592@1] [0x1b7e] = 0xff
• [    0.918376@1] [0x105f] = 0x0
• [    0.921252@1] [0x109d] = 0x814d3928
• [    0.924713@1] [0x109e] = 0x6b425012
• [    0.928185@1] [0x109f] = 0x110
• [    0.931229@1] [0x109c] = 0x1043e
• [    0.934434@1] [0x1066] = 0x10843
• [    0.937646@1] [0x1059] = 0x100
• [    0.940684@1] [0x105f] = 0x80000
• [    0.943902@1] [0x105f] = 0x88001
• [    0.947107@1] [0x105f] = 0x80003
• [    0.950319@1] [0x104a] = 0x101
• [    0.953362@1] [0x107f] = 0x8c0000c3
• [    0.956829@1] [0x1bb8] = 0x52
• [    0.959780@1] [0x1b62] = 0x2029
• [    0.962909@1] [0x1b8d] = 0x4040
• [    0.966030@1] [0x1b8e] = 0x19
• [    0.968981@1] [0x1b94] = 0x288
• [    0.972024@1] [0x1b95] = 0xc87
• [    0.975057@1] [0x1b97] = 0xce3
• [    0.978095@1] [0x1b98] = 0x50
• [    0.981046@1] [0x1b99] = 0xf0
• [    0.984001@1] [0x1b9a] = 0x50
• [    0.986949@1] [0x1b9b] = 0x2b0
• [    0.989987@1] [0x1b9c] = 0xcb0
• [    0.993028@1] [0x1b9d] = 0x4
• [    0.995889@1] [0x1b9e] = 0x8
• [    0.998753@1] [0x1ba1] = 0x4
• [    1.001621@1] [0x1ba2] = 0x8
• [    1.004482@1] [0x1ba4] = 0x288
• [    1.007520@1] [0x1ba3] = 0xc87
• [    1.010558@1] [0x1ba6] = 0x1d
• [    1.013513@1] [0x1baf] = 0x2ec
• [    1.016547@1] [0x1ba7] = 0x100
• [    1.019585@1] [0x1ba8] = 0xa8
• [    1.022548@1] [0x1ba9] = 0xa8
• [    1.025488@1] [0x1baa] = 0x100
• [    1.028525@1] [0x1bab] = 0x0
• [    1.031394@1] [0x1bac] = 0x5
• [    1.034254@1] [0x1bae] = 0x2ed
• [    1.037292@1] [0x1b68] = 0x100
• [    1.040330@1] [0x1b60] = 0x0
• [    1.043198@1] [0x1b6e] = 0x200
• [    1.046233@1] [0x1b58] = 0x0
• [    1.049097@1] [0x1b7e] = 0x0
• [    1.051965@1] [0x1b64] = 0x9061
• [    1.055087@1] [0x1b65] = 0xa061
• [    1.058211@1] [0x1b66] = 0xb061
• [    1.061340@1] [0x1b78] = 0x1
• [    1.064201@1] [0x1b79] = 0x1
• [    1.067065@1] [0x1b7a] = 0x1
• [    1.069929@1] [0x1b7b] = 0x1
• [    1.072798@1] [0x1b7c] = 0x1
• [    1.075658@1] [0x1b7d] = 0x1
• [    1.078523@1] [0x271a] = 0xa
• [    1.081391@1] [0x1bfc] = 0x1000
• [    1.084512@1] [0x1c0d] = 0x3102
• [    1.087637@1] [0x1c0e] = 0x54
• [    1.090588@1] [0x1b80] = 0x1
• [    1.093456@1] [0x1b57] = 0x0
• [    1.096318@1] tvoutc_setmode[267]
• [    1.099616@1] mode is: 6
• [    1.102139@1] VPU_VIU_VENC_MUX_CTRL: 0xa
• [    1.106038@1] viu chan = 1
• [    1.108729@1] VPU_VIU_VENC_MUX_CTRL: 0xa
• [    1.191513@1] request_fiq:152: fiq=35
• [    1.191541@1] request_fiq:186: end
• [    1.225052@0] print_constraints: vcck: 1010 <--> 1370 mV at 1380 mV
• [    1.226229@0] Advanced Linux Sound Architecture Driver Version 1.0.24.
• [    1.232962@0] Bluetooth: Core ver 2.16
• [    1.236106@0] NET: Registered protocol family 31
• [    1.240606@0] Bluetooth: HCI device and connection manager initialized
• [    1.247149@0] Bluetooth: HCI socket layer initialized
• [    1.252189@0] Bluetooth: L2CAP socket layer initialized
• [    1.257376@0] Bluetooth: SCO socket layer initialized
• [    1.263447@1] Switching to clocksource Timer-E
• [    1.271222@0] Switched to NOHz mode on CPU #0
• [    1.271230@1] Switched to NOHz mode on CPU #1
• [    1.276883@0] cfg80211: Calling CRDA to update world regulatory domain
• [    1.287372@1] NET: Registered protocol family 2
• [    1.287514@1] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
• [    1.294040@1] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
• [    1.301813@1] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
• [    1.308627@1] TCP: Hash tables configured (established 65536 bind 65536)
• [    1.314562@1] TCP reno registered
• [    1.318211@1] HDMI: EDID Ready
• [    1.321006@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
• [    1.326961@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
• [    1.333339@1] CEC: Physical address: 0x1000
• [    1.337491@1] CEC: Physical address: 1.0.0.0
• [    1.341771@1] HDMI: get current mode: 720p
• [    1.345826@1] set mode VIC 4 (cd0,cs0,pm1,vd0,1)
• [    1.347173@0] NET: Registered protocol family 1
• [    1.347354@0] Unpacking initramfs...
• [    1.358612@1] HDMI DEBUG: hdmi_hw_reset [1377]
• [    1.363001@1] HDMI: get brd phy data
• [    1.366551@1] hdmi phy setting
• [    1.370701@1] HDMI: get brd phy data
• [    1.373149@1] hdmi phy setting
• [    1.376240@1] HDMI DEBUG: hdmitx_set_pll [2058]
• [    1.380730@1] param->VIC:4
• [    1.383393@1] mode is: 6
• [    1.385912@1] VPU_VIU_VENC_MUX_CTRL: 0xa
• [    1.389837@1] viu chan = 1
• [    1.392505@1] VPU_VIU_VENC_MUX_CTRL: 0xa
• [    1.402734@0] Freeing initrd memory: 1068K
• [    1.403988@0] highmem bounce pool size: 64 pages
• [    1.406035@0] ashmem: initialized
• [    1.419980@1] Sink is HDMI device
• [    1.420022@1] Source in HDMI Mode
• [    1.421156@1] CEC not ready
• [    1.424027@0] NTFS driver 2.1.30 [Flags: R/O].
• [    1.428566@0] fuse init (API version 7.16)
• [    1.432866@0] msgmni has been set to 570
• [    1.437033@0] io scheduler noop registered
• [    1.440221@0] io scheduler deadline registered (default)
• [    1.526931@1] HDMI: audio channel num is 0
• [    1.526989@1] current VIC: 4
• [    1.528251@1] audio sample rate: 0
• [    1.531636@1] HDMI: reset audio N para
• [    1.535374@1] PCM out to HDMI
• [    1.561698@1] Time out: AIU_HDMI_CLK_DATA_CTRL
• [    1.561742@1] i2s_to_spdif_flag:1
• [    1.563891@1] Enable audio spdif to HDMI
• [    1.567882@1] HDMI: set audio param
• [    1.624675@0] loop: module loaded
• [    1.626919@0] PPP generic driver version 2.4.2
• [    1.627436@0] PPP Deflate Compression module registered
• [    1.631987@0] PPP BSD Compression module registered
• [    1.637250@0] PPP MPPE Compression module registered
• [    1.641797@0] NET: Registered protocol family 24
• [    1.646400@0] tun: Universal TUN/TAP device driver, 1.6
• [    1.651656@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
• [    1.658811@0] usbcore: registered new interface driver cdc_acm
• [    1.663756@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
• [    1.671945@0] Initializing USB Mass Storage driver...
• [    1.677095@0] usbcore: registered new interface driver usb-storage
• [    1.683111@0] USB Mass Storage support registered.
• [    1.688121@0] usbcore: registered new interface driver usbserial
• [    1.693875@0] usbserial: USB Serial Driver core
• [    1.698500@0] USB Serial support registered for GSM modem (1-port)
• [    1.704646@0] usbcore: registered new interface driver option
• [    1.710295@0] option: v0.7.2:USB Driver for GSM modems
• [    1.716167@0] mousedev: PS/2 mouse device common for all mice
• [    1.722398@0] usbcore: registered new interface driver iforce
• [    1.728046@0] usbcore: registered new interface driver xpad
• [    1.732611@0] usbcore: registered new interface driver usb_nanosic_ts
• [    1.739765@0] i2c /dev entries driver
• [    1.742800@0] lirc_dev: IR Remote Control driver registered, major 250
• [    1.749109@0] IR NEC protocol handler initialized
• [    1.753767@0] IR RC5(x) protocol handler initialized
• [    1.758724@0] IR RC6 protocol handler initialized
• [    1.763402@0] IR JVC protocol handler initialized
• [    1.768098@0] IR Sony protocol handler initialized
• [    1.772863@0] IR RC5 (streamzap) protocol handler initialized
• [    1.778601@0] IR LIRC bridge handler initialized
• [    1.783192@0] Linux video capture interface: v2.00
• [    1.788210@0] usbcore: registered new interface driver uvcvideo
• [    1.793869@0] USB Video Class driver (v1.1.0)
• [    1.799024@0] device-mapper: uevent: version 1.0.3
• [    1.803653@0] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
• [    1.811849@0] Bluetooth: HCI UART driver ver 2.2
• [    1.816180@0] Bluetooth: HCI H4 protocol initialized
• [    1.821173@0] cpuidle: using governor ladder
• [    1.825378@0] cpuidle: using governor menu
• [    1.830598@0] usbcore: registered new interface driver usbhid
• [    1.835186@0] usbhid: USB HID core driver
• [    1.839965@0] logger: created 256K log 'log_main'
• [    1.844128@0] logger: created 256K log 'log_events'
• [    1.849002@0] logger: created 256K log 'log_radio'
• [    1.853749@0] logger: created 256K log 'log_system'
• [    1.858490@0] vout_init_module
• [    1.861438@0] start init vout module
• [    1.865229@0] create  vout attribute ok
• [    1.869246@0] ge2d_init
• [    1.871561@0] ge2d_dev major:248
• [    1.875324@0] ge2d start monitor
• [    1.878210@0] osd_init
• [    1.878215@1] ge2d workqueue monitor start
• [    1.884702@0] [osd0] 0x84100000-0x850fffff
• [    1.888983@0] Frame buffer memory assigned at phy:0x84100000, vir:0xe1000000, size=16384K
• [    1.896914@0] ---------------clear framebuffer0 memory
• [    1.914859@0] [osd1] 0x85100000-0x851fffff
• [    1.914911@0] Frame buffer memory assigned at phy:0x85100000, vir:0xe0200000, size=1024K
• [    1.921401@0] init fbdev bpp is :24
• [    1.926063@0] osd probe ok
• [    1.934536@0] amlvideo-000: V4L2 device registered as video10
• [    1.935327@0]  set pinmux c08753d8
• [    1.938073@0]  set pinmux c08753e0
• [    1.966893@0] UART_ttyS0irq = 122)
• [    1.996888@0] UART_ttyS1irq = 58)
• [    1.997045@0] dwc_otg: version 2.94a 05-DEC-2012
• [    2.499228@0] USB (0) use clock source: XTAL input
• [    2.566864@1] HDMITX: no HDCP key available
• [    2.566888@1] HDMITX: HDCP Key error
• [    2.568964@1] HDMITX: no HDCP key available
• [    2.573125@1] HDMITX: HDCP Key error
• [    2.900179@0] Core Release: 2.94a
• [    2.900202@0] Setting default values for core params
• [    3.302808@0] Using Buffer DMA mode
• [    3.302831@0] OTG VER PARAM: 1, OTG VER FLAG: 1
• [    3.305163@0] Working on port type = HOST
• [    3.309241@0] dwc_otg lm0: DWC OTG Controller
• [    3.313580@0] dwc_otg lm0: new USB bus registered, assigned bus number 1
• [    3.320239@0] dwc_otg lm0: irq 62, io mem 0x00000000
• [    3.328249@0] Init: Port Power? op_state=1
• [    3.329207@0] Init: Power Port (0)
• [    3.333440@0] hub 1-0:1.0: USB hub found
• [    3.336510@0] hub 1-0:1.0: 1 port detected
• [    3.740932@0] Core Release: 2.94a
• [    3.740954@0] Setting default values for core params
• [    4.143569@0] Using Buffer DMA mode
• [    4.143592@0] OTG VER PARAM: 1, OTG VER FLAG: 1
• [    4.145927@0] Working on port type = HOST
• [    4.149993@0] dwc_otg lm1: DWC OTG Controller
• [    4.154292@0] dwc_otg lm1: new USB bus registered, assigned bus number 2
• [    4.160994@0] dwc_otg lm1: irq 63, io mem 0x00000000
• [    4.168975@0] Init: Port Power? op_state=1
• [    4.169970@0] Init: Power Port (0)
• [    4.174169@0] hub 2-0:1.0: USB hub found
• [    4.177315@0] hub 2-0:1.0: 1 port detected
• [    4.181733@0] Amlogic nand flash Kernel driver, Version K1.06.015 (c) 2010 Amlogic Inc.
• [    4.189363@0] ####Version of Uboot must be newer than U1.06.011!!!!!
• [    4.195795@0] 2
• [    4.197521@0] SPI BOOT, m3_nand_probe continue i 0
• [    4.202263@0] chip->controller=c09ed01c
• [    4.206079@0] checking ChiprevD :0
• [    4.209492@0] aml_nand_probe checked chiprev:0
• [    4.213904@0] init bus_cycle=17, bus_timing=10, start_cycle=10, end_cycle=10,system=5.0ns
• [    4.222505@0] No NAND device found.
• [    4.225763@0] NAND device id: 98 d7 84 93 72 57
• [    4.230158@0] NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
• [    4.240248@0] #####aml_nand_init, with RB pins and chip->chip_delay:20
• [    4.246620@0] bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
• [    4.254020@0] oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
• [    4.264518@0] aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
• [    4.271896@0] multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
• [    4.282421@0]  oob layout use nand base oob layout oobsize = 32,oobmul =1,mtd->oobsize =1280,aml_chip->oob_size =1280
• [    4.300444@0] aml nand env valid addr: 8000
• [    4.317160@0] nand env: nand_env_probe.
• [    4.317867@0] nand key: nand_key_probe.
• [    4.319359@0] key start_blk=1016,end_blk=1023,aml_nand_key_init:651
• [    4.331532@0] aml nand key valid addr: fe000000
• [    4.331557@0] aml nand key valid addr: fe400000
• [    4.335107@0] aml nand key valid addr: fe800000
• [    4.339735@0] aml nand key valid addr: fec00000
• [    4.344359@0] i=0,register --- nand_key NAND bbt detect factory Bad block at 7b000000
• [    4.353523@0]  NAND bbt detect factory Bad block at 8b800000
• [    4.357969@0] Creating 12 MTD partitions on "A serials NAND 4GiB TC58TEG5DCJTA00 ":
• [    4.365579@0] 0x000000800000-0x000001000000 : "bootargs"
• [    4.374934@0] 0x000001000000-0x000001800000 : "misc"
• [    4.376975@1] Indeed it is in host mode hprt0 = 00021501
• [    4.384033@0] 0x000001800000-0x000002000000 : "baseparam"
• [    4.387842@0] 0x000002000000-0x000002800000 : "logo"
• [    4.392644@0] 0x000002800000-0x000003800000 : "aml_logo"
• [    4.398035@0] 0x000003800000-0x000009800000 : "fastplay"
• [    4.403250@0] 0x000009800000-0x00000a800000 : "recovery"
• [    4.408672@0] 0x00000a800000-0x00000b800000 : "boot"
• [    4.413521@0] 0x00000b800000-0x00002b800000 : "system"
• [    4.418820@0] 0x00002b800000-0x00004b800000 : "cache"
• [    4.423681@0] 0x00004b800000-0x00008c000000 : "userdata"
• [    4.427869@0]  NAND bbt detect factory Bad block at 7b000000
• [    4.433454@0]  NAND bbt detect factory Bad block at 8b800000
• [    4.440480@0] 0x00008c000000-0x0000fe000000 : "NFTL_Part"
• [    4.444591@0]  NAND bbt detect factory Bad block at a0000000
• [    4.450488@0]  NAND bbt detect factory Bad block at a0800000
• [    4.456018@0]  NAND bbt detect factory Bad block at a1800000
• [    4.461798@0]  NAND bbt detect factory Bad block at d2000000
• [    4.467507@0]  NAND bbt detect factory Bad block at ef400000
• [    4.474594@0] init_aml_nftl start
• [    4.476512@0] mtd->name: system
• [    4.479721@0] nftl version 131218a
• [    4.483023@0] nftl part attr 0
• [    4.486068@0] nftl start:128,16
• [    4.489532@0] first
• [    4.528891@0] second 128,112
• [    4.556926@1] usb 2-1: new high speed USB device number 2 using dwc_otg
• [    4.558193@1] Indeed it is in host mode hprt0 = 00001101
• [    4.614591@0] current used block :85
• [    4.627028@0] free block cnt = 46
• [    4.627047@0] nftl ok!
• [    4.627565@0] aml_nftl_blk->mbd.tr.name =system
• [    4.632349@1] aml_nftl_init_bounce_buf, use cache here
• [    4.637449@0]  system: unknown partition table
• [    4.641421@0] _nftl_init_bounce_buf already init 1000
• [    4.646135@0] aml_nftl_add_mtd ok
• [    4.649486@0] mtd->name: cache
• [    4.652477@0] nftl version 131218a
• [    4.655869@0] nftl part attr 0
• [    4.658951@0] nftl start:128,16
• [    4.662339@0] first
• [    4.703008@0] second 95,112
• [    4.759796@1] hub 2-1:1.0: USB hub found
• [    4.760147@1] hub 2-1:1.0: 4 ports detected
• [    4.766960@0] current used block :33
• [    4.864810@0] free block cnt = 64
• [    4.864829@0] nftl ok!
• [    4.865334@0] aml_nftl_blk->mbd.tr.name =cache
• [    4.870239@1] aml_nftl_init_bounce_buf, use cache here
• [    4.875116@0]  cache: unknown partition table
• [    4.879113@0] _nftl_init_bounce_buf already init 1000
• [    4.883760@0] aml_nftl_add_mtd ok
• [    4.887102@0] mtd->name: userdata
• [    4.890351@0] nftl version 131218a
• [    4.893757@0] nftl part attr 0
• [    4.896793@0]  NAND bbt detect factory Bad block at 7b000000
• [    4.902537@0]  NAND bbt detect factory Bad block at 8b800000
• [    4.908255@0] size_in_blk 258; total_block 256;
• [    4.912824@0] nftl start:256,32
• [    4.916498@0] first
• [    4.981567@0]  NAND bbt detect factory Bad block at 7b000000
• [    5.001254@0]  NAND bbt detect factory Bad block at 8b800000
• [    5.001653@0] second 55,224
• [    5.040944@0] current used block :202
• [    5.093566@0] free block cnt = 203
• [    5.093585@0] nftl ok!
• [    5.094546@0] aml_nftl_blk->mbd.tr.name =data
• [    5.098811@1] aml_nftl_init_bounce_buf, use cache here
• [    5.103878@0]  data: unknown partition table
• [    5.107788@0] _nftl_init_bounce_buf already init 1000
• [    5.112421@0] aml_nftl_add_mtd ok
• [    5.115720@0] mtd->name: NFTL_Part
• [    5.119151@0] nftl version 131218a
• [    5.122530@0] nftl part attr 0
• [    5.125543@0]  NAND bbt detect factory Bad block at a0000000
• [    5.131289@0]  NAND bbt detect factory Bad block at a0800000
• [    5.137027@0]  NAND bbt detect factory Bad block at a1800000
• [    5.142750@0]  NAND bbt detect factory Bad block at d2000000
• [    5.148482@0]  NAND bbt detect factory Bad block at ef400000
• [    5.154180@0] size_in_blk 456; total_block 451;
• [    5.158797@0] nftl start:451,56
• [    5.163041@0] first
• [    5.190717@0]  NAND bbt detect factory Bad block at a0000000
• [    5.191163@0]  NAND bbt detect factory Bad block at a0800000
• [    5.197557@0]  NAND bbt detect factory Bad block at a1800000
• [    5.266636@0]  NAND bbt detect factory Bad block at d2000000
• [    5.305437@0]  NAND bbt detect factory Bad block at ef400000
• [    5.324903@0] second 0,395
• [    5.324924@0] all block full!!
• [    5.325006@0] free block cnt = 451
• [    5.328417@0] nftl ok!
• [    5.331702@0] aml_nftl_blk->mbd.tr.name =media
• [    5.335911@1] aml_nftl_init_bounce_buf, use cache here
• [    5.340389@0]  media: unknown partition table
• [    5.344923@0] _nftl_init_bounce_buf already init 1000
• [    5.349696@0] aml_nftl_add_mtd ok
• [    5.352956@0] init_aml_nftl end
• [    5.356081@0] ethernetinit(dbg[c086b338]=1)
• [    5.360302@0] ethernet base addr is f3610000
• [    5.364498@0] set_phy_mode() phy_Identifier: 0x0
• [    5.369263@0] ethernet: MII PHY 0007c0f1h found at address 1, status 0x7809 advertising 01e1.
• [    5.377712@0] find phy phy_Identifier=7c0f1
• [    5.381770@0] write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
• [    5.388460@0] eth0: mixed no checksumming and other settings.
• [    5.394215@0] Amlogic A/V streaming port init
• [    5.401988@0] regist mpeg12 codec profile
• [    5.402177@0] regist mpeg4 codec profile
• [    5.405989@0] amvdec_vc1 module init
• [    5.409720@0] regist vc1 codec profile
• [    5.413280@0] amvdec_h264 module init
• [    5.417082@0] regist h264 codec profile
• [    5.420744@0] amvdec_h264mvc module init
• [    5.424847@0] regist mjpeg codec profile
• [    5.428590@0] amvdec_real module init
• [    5.432306@0] regist real codec profile
• [    5.437177@0] Vsync pts inc(before): 1500
• [    5.440016@0] Vsync pts inc(after): 1500
• [    5.443921@0] request_fiq:152: fiq=35
• [    5.447607@0] request_fiq:186: end
• [    5.451640@0] Remote Driver
• [    5.454142@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
• [    5.461706@0] meson_remote_pinmux_setup()
• [    5.464928@0] Remote platform_data g_remote_base=f3100480
• [    5.470356@0] Remote date_valye======0,status == 8915d20
• [    5.475632@0] remote config major:244
• [    5.479861@0] physical address:0x9f950000
• [    5.483429@0] Meson KeyInput init
• [    5.486685@0] Key 117 registed.
• [    5.489800@0] Key 116 registed.
• [    5.493091@0] input: key_input as /devices/platform/meson-keyinput.0/input/input1
• [    5.500779@0] Meson KeyInput register RTC interrupt
• [    5.505054@0] Meson KeyInput major=243
• [    5.509993@0]  spi_nor_probe 586
• [    5.512147@0] SPI BOOT  : spi_nor_probe 591
• [    5.516419@0] spi_nor apollospi:0: mx25l3205d (4096 Kbytes)
• [    5.522003@0] Creating 2 MTD partitions on "apollospi:0":
• [    5.527369@0] 0x000000000000-0x000000400000 : "bootloader"
• [    5.534241@0] 0x000000080000-0x000000088000 : "ubootenv"
• [    5.540010@0] Memory Card media Major: 253
• [    5.542325@0] card max_req_size is 128K
• [    5.546793@0] card creat process sucessful
• [    5.550265@0]
• [    5.550269@0] SD/MMC initialization started......
• [    6.186866@0] mmc data3 pull high
• [    6.187090@0] sd_mmc_info->card_type=0
• [    6.188274@0] begin SDIO check ......
• [    6.214491@0] sdio_timeout_int_times = 0; timeout = 498
• [    6.237087@0] sdio_timeout_int_times = 0; timeout = 497
• [    6.237114@0] SEND OP timeout @1
• [    6.239877@0] mmc data3 pull high
• [    6.243366@0] begin SD&SDHC check ......
• [    6.289431@0] sdio_timeout_int_times = 0; timeout = 498
• [    6.289458@0] SEND IF timeout @2
• [    6.314984@0] sdio_timeout_int_times = 0; timeout = 498
• [    6.315011@0] begin MMC check ......
• [    6.359427@0] sdio_timeout_int_times = 0; timeout = 498
• [    6.359456@0] No any SD/MMC card detected!
• [    6.363092@0] #SD_MMC_ERROR_DRIVER_FAILURE error occured in sd_voltage_validation()
• [    6.370761@0] [card_force_init] unit_state 3
• [    6.375141@0] [dsp]DSP start addr 0xc4000000
• [    6.379304@0] [dsp]register dsp to char divece(232)
• [    6.389259@0] DSP pcmenc stream buffer to [0x9e401000-0x9e601000]
• [    6.390175@0] amlogic audio dsp pcmenc device init!
• [    6.395923@0] amlogic audio spdif interface device init!
• [    6.401619@0] using rtc device, aml_rtc, for alarms
• [    6.405047@0] aml_rtc aml_rtc: rtc core: registered aml_rtc as rtc0
• [    6.412367@0] efuse===========================================
• [    6.417942@0] efuse: device efuse created
• [    6.421359@0] efuse--------------------------------------------
• [    6.427255@0] keys===========================================
• [    6.432882@0] keys_devno=ee00000
• [    6.436612@0] efuse: device aml_keys created
• [    6.440398@0] amlkeys=0
• [    6.442878@0] platform_driver_register--aml_keys_driver--------------------
• [    6.466876@0] 6amlogic audio data interface device init!
• [    6.467560@0] amlogic rfkill init
• [    6.497046@0] BT_RADIO going: on
• [    6.497067@0] BCM_BT: going ON
• [    6.557063@0] aml_hw_crypto initialization.
• [    6.558023@0] usbcore: registered new interface driver snd-usb-audio
• [    6.562876@0] enter dummy_codec_audio_probe
• [    6.566304@0] sound card index = #0
• [    6.569468@0] sound card index = #(null)
• [    6.573661@0] aml-pcm 0:playback preallocate_dma_buffer: area=ffdf0000, addr=9f0f8000, size=16384
• [    6.582768@0] iec958 0: preallocate dma buffer start=ffde0000, size=10000
• [    6.589783@0] aml-pcm 1:capture preallocate_dma_buffer: area=ffda0000, addr=9f340000, size=65536
• [    6.597917@0] asoc: dummy_codec <-> aml-dai0 mapping ok
• [    6.604552@0] ALSA device list:
• [    6.606211@0]   #0: AML-DUMMY-CODEC
• [    6.609897@0] GACT probability NOT on
• [    6.613336@0] Mirror/redirect action on
• [    6.617192@0] u32 classifier
• [    6.620011@0]     Actions configured
• [    6.623572@0] Netfilter messages via NETLINK v0.30.
• [    6.628509@0] nf_conntrack version 0.5.0 (12752 buckets, 51008 max)
• [    6.635431@0] ctnetlink v0.93: registering with nfnetlink.
• [    6.640238@0] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
• [    6.647300@0] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
• [    6.653985@0] xt_time: kernel timezone is -0000
• [    6.657994@0] ip_tables: (C) 2000-2006 Netfilter Core Team
• [    6.663382@0] arp_tables: (C) 2002 David S. Miller
• [    6.668117@0] TCP cubic registered
• [    6.672554@0] NET: Registered protocol family 10
• [    6.676817@0] Mobile IPv6
• [    6.678717@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
• [    6.684281@0] IPv6 over IPv4 tunneling driver
• [    6.689828@0] NET: Registered protocol family 17
• [    6.693136@0] NET: Registered protocol family 15
• [    6.697897@0] Bridge firewalling registered
• [    6.701983@0] Bluetooth: RFCOMM TTY layer initialized
• [    6.706958@0] Bluetooth: RFCOMM socket layer initialized
• [    6.712195@0] Bluetooth: RFCOMM ver 1.11
• [    6.716101@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
• [    6.721601@0] Bluetooth: BNEP filters: protocol multicast
• [    6.726989@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
• [    6.733231@0] NET: Registered protocol family 35
• [    6.737990@0] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
• [    6.745447@0] DDR low power is enable.
• [    6.749248@0] enter meson_pm_probe!
• [    6.752647@0] meson_pm_probe done !
• [    6.756601@0] ------------[ cut here ]------------
• [    6.760907@0] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/kernel/smp.c:459 smp_call_function_many+0xc8/0x280()
• [    6.771647@0] Modules linked in:
• [    6.774884@0] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
• [    6.784415@0] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f18>] (warn_slowpath_null+0x1c/0x24)
• [    6.794222@0] [<c0061f18>] (warn_slowpath_null+0x1c/0x24) from [<c008f598>] (smp_call_function_many+0xc8/0x280)
• [    6.804292@0] [<c008f598>] (smp_call_function_many+0xc8/0x280) from [<c008f784>] (smp_call_function+0x34/0x68)
• [    6.814276@0] [<c008f784>] (smp_call_function+0x34/0x68) from [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc)
• [    6.823560@0] [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc) from [<c0049f28>] (meson_clk_set_rate+0x130/0x168)
• [    6.833108@0] [<c0049f28>] (meson_clk_set_rate+0x130/0x168) from [<c0049ff4>] (clk_set_rate+0x94/0xbc)
• [    6.842397@0] [<c0049ff4>] (clk_set_rate+0x94/0xbc) from [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224)
• [    6.853072@0] [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224) from [<c0052e24>] (meson_cpufreq_target+0x24/0x3c)
• [    6.864445@0] [<c0052e24>] (meson_cpufreq_target+0x24/0x3c) from [<c0370570>] (__cpufreq_driver_target+0x50/0x64)
• [    6.874688@0] [<c0370570>] (__cpufreq_driver_target+0x50/0x64) from [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30)
• [    6.885622@0] [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30) from [<c0370658>] (__cpufreq_governor+0xb0/0x138)
• [    6.896211@0] [<c0370658>] (__cpufreq_governor+0xb0/0x138) from [<c03714b8>] (__cpufreq_set_policy+0x128/0x168)
• [    6.906280@0] [<c03714b8>] (__cpufreq_set_policy+0x128/0x168) from [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8)
• [    6.917043@0] [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8) from [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634)
• [    6.927375@0] [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634) from [<c029aa98>] (sysdev_driver_register+0xb0/0x12c)
• [    6.937356@0] [<c029aa98>] (sysdev_driver_register+0xb0/0x12c) from [<c0370b24>] (cpufreq_register_driver+0x70/0x17c)
• [    6.947947@0] [<c0370b24>] (cpufreq_register_driver+0x70/0x17c) from [<c029d318>] (platform_drv_probe+0x18/0x1c)
• [    6.958101@0] [<c029d318>] (platform_drv_probe+0x18/0x1c) from [<c029c10c>] (driver_probe_device+0x90/0x1ac)
• [    6.967908@0] [<c029c10c>] (driver_probe_device+0x90/0x1ac) from [<c029c2b4>] (__driver_attach+0x8c/0x90)
• [    6.977456@0] [<c029c2b4>] (__driver_attach+0x8c/0x90) from [<c029b32c>] (bus_for_each_dev+0x5c/0x88)
• [    6.986656@0] [<c029b32c>] (bus_for_each_dev+0x5c/0x88) from [<c029baf0>] (bus_add_driver+0x17c/0x244)
• [    6.995944@0] [<c029baf0>] (bus_add_driver+0x17c/0x244) from [<c029c760>] (driver_register+0x78/0x13c)
• [    7.005232@0] [<c029c760>] (driver_register+0x78/0x13c) from [<c029d6c8>] (platform_driver_probe+0x18/0x9c)
• [    7.014959@0] [<c029d6c8>] (platform_driver_probe+0x18/0x9c) from [<c003770c>] (do_one_initcall+0xfc/0x164)
• [    7.024679@0] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
• [    7.033617@0] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
• [    7.042554@0] ---[ end trace 1b75b31a2719ed1d ]---
• [    7.047327@0] ------------[ cut here ]------------
• [    7.052103@0] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/kernel/smp.c:320 smp_call_function_single+0x150/0x1c0()
• [    7.063122@0] Modules linked in:
• [    7.066342@0] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
• [    7.075887@0] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f18>] (warn_slowpath_null+0x1c/0x24)
• [    7.085696@0] [<c0061f18>] (warn_slowpath_null+0x1c/0x24) from [<c008f460>] (smp_call_function_single+0x150/0x1c0)
• [    7.096026@0] [<c008f460>] (smp_call_function_single+0x150/0x1c0) from [<c008f784>] (smp_call_function+0x34/0x68)
• [    7.106268@0] [<c008f784>] (smp_call_function+0x34/0x68) from [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc)
• [    7.115555@0] [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc) from [<c0049f28>] (meson_clk_set_rate+0x130/0x168)
• [    7.125103@0] [<c0049f28>] (meson_clk_set_rate+0x130/0x168) from [<c0049ff4>] (clk_set_rate+0x94/0xbc)
• [    7.134391@0] [<c0049ff4>] (clk_set_rate+0x94/0xbc) from [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224)
• [    7.145067@0] [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224) from [<c0052e24>] (meson_cpufreq_target+0x24/0x3c)
• [    7.156438@0] [<c0052e24>] (meson_cpufreq_target+0x24/0x3c) from [<c0370570>] (__cpufreq_driver_target+0x50/0x64)
• [    7.166682@0] [<c0370570>] (__cpufreq_driver_target+0x50/0x64) from [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30)
• [    7.177618@0] [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30) from [<c0370658>] (__cpufreq_governor+0xb0/0x138)
• [    7.188207@0] [<c0370658>] (__cpufreq_governor+0xb0/0x138) from [<c03714b8>] (__cpufreq_set_policy+0x128/0x168)
• [    7.198276@0] [<c03714b8>] (__cpufreq_set_policy+0x128/0x168) from [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8)
• [    7.209039@0] [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8) from [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634)
• [    7.219368@0] [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634) from [<c029aa98>] (sysdev_driver_register+0xb0/0x12c)
• [    7.229350@0] [<c029aa98>] (sysdev_driver_register+0xb0/0x12c) from [<c0370b24>] (cpufreq_register_driver+0x70/0x17c)
• [    7.239941@0] [<c0370b24>] (cpufreq_register_driver+0x70/0x17c) from [<c029d318>] (platform_drv_probe+0x18/0x1c)
• [    7.250096@0] [<c029d318>] (platform_drv_probe+0x18/0x1c) from [<c029c10c>] (driver_probe_device+0x90/0x1ac)
• [    7.259904@0] [<c029c10c>] (driver_probe_device+0x90/0x1ac) from [<c029c2b4>] (__driver_attach+0x8c/0x90)
• [    7.269452@0] [<c029c2b4>] (__driver_attach+0x8c/0x90) from [<c029b32c>] (bus_for_each_dev+0x5c/0x88)
• [    7.278653@0] [<c029b32c>] (bus_for_each_dev+0x5c/0x88) from [<c029baf0>] (bus_add_driver+0x17c/0x244)
• [    7.287940@0] [<c029baf0>] (bus_add_driver+0x17c/0x244) from [<c029c760>] (driver_register+0x78/0x13c)
• [    7.297228@0] [<c029c760>] (driver_register+0x78/0x13c) from [<c029d6c8>] (platform_driver_probe+0x18/0x9c)
• [    7.306950@0] [<c029d6c8>] (platform_driver_probe+0x18/0x9c) from [<c003770c>] (do_one_initcall+0xfc/0x164)
• [    7.316671@0] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
• [    7.325611@0] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
• [    7.334548@0] ---[ end trace 1b75b31a2719ed1e ]---
• [    7.342779@0] ERROR::usb_gadget_probe_driver:1316: usb_gadget_register_driver ENODEV
• [    7.342784@0]
• [    7.349288@0] aml_rtc aml_rtc: setting system clock to 1970-01-01 00:00:12 UTC (12)
• [    7.356342@0] CEC init
• [    7.358776@1] CEC: CEC task process
• [    7.362216@0] i[    7.386878@0] Changing baud from 0 to 115200
• [    7.446933@0] Freeing init memory: 188K
• [    7.450392@1] init: /init.amlogic.rc: 373: ignored duplicate definition of service 'smbd'
• [    7.453900@1] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
• [    7.462543@1] init: try mount debugfs to target /sys/kernel/debug
• [    7.468302@1] init: try mount none to target /proc/bus/usb
• [    7.480523@1] UMP: UMP device driver  loaded
• [    7.504792@1] Mali pp1 MMU register mapped at e001e000...
• [    7.504848@1] Mali pp2 MMU register mapped at e00cc000...
• [    7.509973@1] mali_meson_poweron: Mali APB bus accessing
• [    7.515226@1] ..........accessing done.
• [    7.582058@1] mali_meson_poweron: Interrupt received.
• [    7.648808@1] Mali: Mali device driver loaded
• [    8.650017@1] init: try mount none to target /acct
• [    8.687267@0] init: try mount tmpfs to target /mnt/secure
• [    8.687477@0] init: try mount tmpfs to target /mnt/asec
• [    8.692340@0] init: try mount tmpfs to target /mnt/obb
• [    8.698023@0] init: try mount none to target /dev/cpuctl
• [    8.737791@1] init: try mount tmpfs to target /storage/external_storage
• [    8.739037@1] init: try mount /dev/block/system to target /system
• [    8.753480@0] EXT4-fs (system): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
• [    8.757158@0] yaffs: dev is 32505861 name is "mtdblock5" rw
• [    8.762188@0] yaffs: passed flags ""
• [    8.798804@0] init: try mount /dev/block/fastplay to target /fastplay
• [    8.799789@0] vfm_map_store:rm default
• [    8.803385@0] vfm_map_store:add default decoder ppmgr deinterlace amvideo
• [    8.819104@0] init: Before e2fsck_main...
• [    9.061382@0] init: After e2fsck_main...
• [    9.061450@0] init: Before e2fsck_main...
• [    9.063982@0] init: After e2fsck_main...
• [    9.067753@0] init: try mount /dev/block/data to target /data
• [    9.090746@0] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
• [    9.094233@0] init: try mount /dev/block/cache to target /cache
• [    9.139810@0] EXT4-fs (cache): recovery complete
• [    9.143876@0] EXT4-fs (cache): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
• [    9.147765@0] init: cannot find '/system/bin/check_partition', disabling 'check_partition'
• [    9.155843@0] init: try mount rootfs to target /
• [    9.160587@0] init: try mount tmpfs to target /mnt/secure
• [    9.216546@1] set fail , detect locktable conflict,retry
• [    9.245171@0] init: cannot find '/system/bin/cdnclient', disabling 'cdnclient'
• [    9.282151@0] DSP pcmenc stream buffer to [0x9e401000-0x9e601000]
• [    9.292369@0] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
• [    9.317044@0] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
• [    9.324055@0] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
• [    9.347037@0] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
• [    9.357096@0] android_usb:disable, not bind to controller
• [    9.360550@0] android_usb:disable, not bind to controller
• [    9.365387@0] android_usb:enable, not bind to controller
• [    9.380725@0] warning: `adbd' uses 32-bit capabilities (legacy support in use)
• root@android:/ # [    9.431986@0] Write AOBUS[0x0024]=0x0fff0fc3
• [   10.277665@1] kplayer_alsa_ad: open file:/fastplay/adconf.xml failed!
• [   14.686174@0] osd0=>x:1920 ,y:0,w:0,h:0
• [   14.686179@0]  osd1=> x:0,y:0,w:0,h:0
• [   14.718817@0] amvdec_h264 probe start.
• [   14.719026@0]
• [   14.719032@0] vh264_init
• [   14.728786@0] Alloc new mc addr to dea54000
• [   14.741674@0] vf_reg_provider:decoder.h264
• [   14.741792@0] vf_reg_provider:ppmgr
• [   14.778733@0] amvdec_h264 probe end.
• [   14.778868@0] tsdemux video_pid = 0x100, audio_pid = 0x101, sub_pid = 0xffff
• [   14.796496@0] v264dec: aspect_ratio not available from source
• [   14.796605@1] [dsp]dsp_open
• [   14.796611@1] audiodsp prevent sleep
• [   14.809788@1] [dsp]load firmware from userspace failed: switch to load it by calling request_firmware() in kernel
• [   14.900622@0] [dsp]load mcode size=148636
• [   14.900629@0] ,load addr 0xc4000000 mcode name audiodsp_codec_aac_helix.bindi_init_buf: version 2013-9-06a, prog_proc_type 0, buf start 8d200000, size 300000, buf(w720,h584) cur num 5 (available 5,  total 5)
• [   14.923424@0] vf_reg_provider:deinterlace
• [   14.931916@0] [dsp]DSP statck start =0x9e310000,size=0x10000
• [   14.934691@0] [dsp]DSP gp statck start =0x9e16b200,size=0x200
• [   14.947199@0] pre_de_buf_config: source change: 0/0/0/0=>36864/1920/1072/0
• [   14.978984@0] [dsp]DSP heap start =0x9e800000,size=0x100000
• [   14.986556@0] [dsp]DSP stream buffer to [0x9e328000-0x9e32ffe0]
• [   14.987203@0] reset dsp : dec opt=fffb, subid=0
• [   15.001437@0] [dsp]dsp reset now
• [   15.056516@0] [dsp]frame format changed,fmt->valid 0x1c
• [   15.056668@0] [dsp]audio info from dsp:sample_rate=48000 channel_num=2
• [   15.064938@0] [dsp]dsp status=52756e
• [   15.128044@0] substream#0 ptr: dfb72f00 type: playback name: subdevice #0 interface: I2S
• [   15.144953@0] ====== audio_set_aiubuf ======
• [   15.145077@0] I2S hw init,i2s mode 0
• [   15.157363@0] iec958 mode PCM16
• [   15.157512@0] IEC958 16bit
• [   15.157643@0] iec958 nodify hdmi audio type 1
• [   15.185667@0] audio info changed.notify to hdmi: type 1,sr 48000,ch 2
• [   15.186541@0] HDMI: aout notify rate 48000
• [   15.199841@0] HDMI: aout notify format PCM
• [   15.210770@0] audio pts started::::::: 0
• [   15.212774@0] audio pts started::::::: 1
• [   15.267283@1] HDMI: audio channel num is 1
• [   15.267377@1] current VIC: 4
• [   15.268649@1] audio sample rate: 3
• [   15.272016@1] HDMI: reset audio N para
• [   15.284625@1] PCM out to HDMI
• [   15.284700@1] i2s_to_spdif_flag:1
• [   15.285350@1] Enable audio spdif to HDMI
• [   15.301310@1] HDMI Audio Type: PCM
• [   15.301407@1] HDMI: set audio param
• [   15.607166@1] [887]reset apts:0x22803-->0x2a03f, pcr 0x22803, diff 30780
• [   19.502255@0] 333000
• [   21.171889@0] request_suspend_state: wakeup (3->0) at 20905040005 (1970-01-02 00:00:01.798658999 UTC)
• [   21.310095@1] trun off vdac
• [   21.460118@0] netdev_open
• [   21.460204@0] Ethernet reset
• [   21.460273@0] NET MDA descpter start addr=de194000
• [   21.468495@0] phy_reset!
• [   21.468527@0] set_phy_mode() phy_Identifier: 0x7c0f1
• [   21.474023@0] --1--write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
• [   21.478923@0] name=nand_key nand_key
• [   21.482618@0] read:addr:0xfe000000,phy_blk_addr:1016,phy_page_addr:0,aml_nand_get_key:129
• [   21.495928@0] unkown current key-name,key_read_show:1273
• [   21.496037@0] ret = -22
• [   21.496040@0] print_buff=
• [   21.513211@0] --2--write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
• [   21.514336@0] write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
• [   21.521685@0] Current DMA mode=0, set mode=621c100
• [   21.528291@0] ether leave promiscuous mode
• [   21.529463@0] ether leave all muticast mode
• [   21.533565@0] changed the Multicast,mcount=1
• [   21.537847@0] add mac address:33:33:00:00:00:01,bit=1
• [   21.542852@0] set hash low=2,high=0
• [   21.546355@0] changed the filter setting to :4
• [   21.552598@0] changed the Multicast,mcount=1
• [   21.555022@0] add mac address:33:33:00:00:00:01,bit=1
• [   21.564352@0] changed the Multicast,mcount=2
• [   21.564375@0] add mac address:33:33:00:00:00:01,bit=1
• [   21.564383@0] add mac address:01:00:5e:00:00:01,bit=32
• [   21.564388@0] set hash low=2,high=1
• [   21.564392@0] changed the filter setting to :4
• [   21.564772@0] ADDRCONF(NETDEV_UP): eth0: link is not ready
• [   21.632711@1] changed the Multicast,mcount=2
• [   21.632789@1] add mac address:33:33:00:00:00:01,bit=1
• [   21.636419@1] add mac address:01:00:5e:00:00:01,bit=32
• [   21.673595@1] init: no such service 'wififix'
• [   21.768960@1] +++dhd_module_init+++
• [   21.769288@1] [extern_wifi_set_enable] in
• [   21.770859@1] WIFI  Disenable!
• [   21.976876@1] [extern_wifi_set_enable] in
• [   21.976968@1] WIFI  Enable!
• [   22.367022@1] [extern_wifi_set_enable] in
• [   22.367138@1] WIFI  Enable!
• [   22.368342@1] [extern_wifi_set_enable] in
• [   22.372288@1] WIFI  Enable!
• [   22.375194@1]
• [   22.375203@1] SD/MMC initialization started......
• [   23.016972@1] mmc data3 pull high
• [   23.017318@0] sd_mmc_info->card_type=0
• [   23.018432@0] begin SDIO check ......
• [   23.022918@0] Actual delay time in sdio_voltage_validation() = 10 ms
• [   23.087350@1] Got RCA = 1
• [   23.089457@0] #this sdio card could not support read after write
• [   23.090615@0] sd_mmc_init() is completed successfully!
• [   23.095635@0] This SDIO card is working in Wide Bus and at 50MHz High Speed mode!
• [   23.095653@0]
• [   23.108526@0] memorycard0: queuing unknown CIS tuple 0x80 (2 bytes)
• [   23.111106@0] memorycard0: queuing unknown CIS tuple 0x80 (3 bytes)
• [   23.116956@1] monitor : INSERT
• [   23.120903@0] memorycard0: queuing unknown CIS tuple 0x80 (3 bytes)
• [   23.128380@1] memorycard0: queuing unknown CIS tuple 0x80 (7 bytes)
• [   23.176955@1] =========== WLAN placed in POWER ON ========
• [   23.178128@1] bcmsdh_register: Linux Kernel SDIO/MMC Driver
• [   23.182527@1] dhd_customer_oob_irq_map: customer specific Host GPIO number is (100)
• [   23.190918@0] dhdsdio_probe : no mutex held. set lock
• [   23.195591@0] F1 signature read @0x18000000=0x1591a962
• [   23.257024@0] bcmsdh_config_hw_oob_intr: Enable HW OOB for 43362
• [   23.262825@0] DHD: dongle ram size is set to 245760(orig 245760)
• [   23.264559@0] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
• [   23.275994@0] wl_create_event_handler thr:e5a created
• [   23.279290@0] wl_create_event_handler thr:e5a started
• [   23.289952@1] p2p0: P2P Interface Registered
• [   23.290292@1] dhd_attach thr:e61 created
• [   23.294164@1] dhd_attach thr:e61 started
• [   23.296796@1] dhd_attach thr:e62 created
• [   23.304542@1] dhd_attach thr:e62 started
• [   23.305058@1] dhd_attach thr:e63 created
• [   23.309340@1] dhd_attach thr:e63 started
• [   23.315271@0] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
• [   23.321204@0] dhdsdio_probe : the lock is released.
• [   23.326407@1] mylin s1 num=2
• [   23.331380@0]
• [   23.331393@0] Dongle Host Driver, version 1.28.23.5 (r)
• [   23.331397@0] Compiled in drivers/net/wireless/bcmdhd on May 13 2014 at 09:49:34
• [   23.447651@0] =========== WLAN placed in RESET ========
• [   23.447694@0] ---dhd_module_init---
• [   25.399020@1] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
• [   25.403209@1]
• [   25.403225@1] Dongle Host Driver, version 1.28.23.5 (r)
• [   25.403238@1] Compiled in drivers/net/wireless/bcmdhd on May 13 2014 at 09:49:34
• [   25.419601@1] wl_android_wifi_on in
• [   25.525363@1] =========== WLAN going back to live  ========
• [   25.525663@0]
• [   25.525666@0]
• [   25.525668@0] dhd_bus_deVReset: == WLAN ON ==
• [   25.534446@0] dhd_bus_devreset called when dongle is not in reset
• [   25.539361@0] Will call dhd_bus_start instead
• [   25.543495@0] bcmsdh_config_hw_oob_intr: Enable HW OOB for 43362
• [   25.549828@0] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
• [   25.559556@0] Final fw_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
• [   25.559572@0] Final nv_path=/etc/wifi/40181/stable/nvram.txt
• [   25.559578@0] Final conf_path=/system/etc/firmware/config.txt
• [   25.603145@0] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
• [   25.836593@0] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
• [   25.837230@0] bcmsdh_set_drvdata: Enter
• [   25.840918@0] bcmsdh_register_oob_intr: Enter
• [   25.845372@0] bcmsdh_register_oob_intr: IRQ=100 Type=414
• [   25.855060@1] Set country ALL, revision 0
• [   25.932228@1] Country code: ALL (ALL/0)
• [   25.940135@1] ------ WIFI Firmware version = wl0: Jul  5 2013 17:55:22 version 5.90.195.89.10 FWID 01-f4d31c13
• [   25.944568@1]   Driver: 1.28.23.5 (r)
• [   25.944576@1]   Firmware: wl0: Jul  5 2013 17:55:22 version 5.90.195.89.10 FWID 01-f4d31c13
• [   25.944629@1] wl_android_wifi_on: Success
• [   25.945912@1] wl_cfg80211_attach_post: p2p0 p2p_dev_addr=02:22:f4:b5:67:2a
• [   30.448099@0] osd0 free scale ENABLE
• [   30.448237@0] vf_reg_providersd
• [   30.459559@0] vf_light_unreg_provider:ppmgr
• [   30.459596@0] ppmgr rebuild from light-unregister
• [   30.460071@0] osd1 free scale ENABLE
• [   30.477232@1] osd0=>x:0 ,y:0,w:0,h:0
• [   30.477248@1]  osd1=> x:0,y:0,w:0,h:0
• [   30.546944@0] <FIQ>:vf_ext_light_unreg_provide
• [   30.546972@0] 0
• [   30.554075@1] vf_unreg_provider:decoder.h264
• [   30.554622@0] vf_unreg_provider:ppmgr
• [   30.556758@0] vf_unreg_provider:deinterlace
• [   30.577000@1] pts missed 10, pts hit 356, pts_outside 0, duration 3840, sync_outside 0, use_idr_framerate 0
• [   30.582439@1] adec_release
• [   30.583999@1] [dsp]dsp_release
• [   30.587047@1] audiodsp allow sleep
• [   30.660174@0] osd0=>x:0 ,y:0,w:1280,h:720
• [   30.660189@0]  osd1=> x:0,y:0,w:18,h:18
• [   30.710723@0] osd0 free scale ENABLE
• [   30.710831@0] vf_reg_providersd
• [   30.746933@0] <FIQ>:vf_ext_light_unreg_provide
• [   30.746952@0] 0
• [   32.001956@1] tvmode set to 720p
• [   32.001976@1]
• [   32.002087@1] don't set the same mode as current.
• [   32.054898@1] osd0 free scale ENABLE
• [   32.055009@1] vf_reg_providersd
• [   32.060148@0] osd1 free scale ENABLE
• [   32.105935@0] buf=0
• [   32.105952@0]
• [   32.106034@0] IEC958_mode_raw=0
• [   32.146916@0] <FIQ>:vf_ext_light_unreg_provide
• [   32.146938@0] 0
• [   32.149409@1] osd[0] set scale, h_scale: DISABLE, v_scale: DISABLE
• [   32.149437@1] osd[0].scaledata: 0 0 0 0
• [   32.149457@1] osd[0].pandata: 0 1279 1080 1799
• [   37.242796@0] trun off vdac
• [   37.776021@1] BT_RADIO going: off
• [   37.776103@1] BCM_BT: going OFF
• [   37.815884@1] BT_RADIO going: on
• [   37.815922@1] BCM_BT: going ON
• [   37.886948@0] Changing baud from 0 to 115200
• [   37.966954@0] Changing baud from 115200 to 115200
• [   38.057658@0] Changing baud from 115200 to 2000000
• [   38.496889@0] Changing baud from 2000000 to 115200
• [   38.776936@0] Changing baud from 115200 to 2000000
• [   39.173928@0] BT_RADIO going: off
• [   39.173971@0] BCM_BT: going OFF
• 
  

复制代码

嗯，TTL接口定义，有需要的拿去用。

更多相关教程，请关注>>乐视盒子论坛

乐视盒子装机必备软件:

电视家浏览器	蜜蜂视频	电视猫视频	沙发管家	沙发桌面

不知道楼主还在玩这个盒子没有。我现在盒子是好的，但我接上TTL线后没有任何屏显，问题可能出现在哪里。端口对的。波率先15200 9600都用了。